Call a Benton commercial roofing contractor who prepares the roof assembly, insulation and edge details Marshall County plan review asks for, then builds the roof to match.
As a Benton commercial roofing contractor, we treat the permit as part of the roof job. The Marshall County Building Office requires permits for every construction project countywide and lists Benton, Calvert City, Hardin and the unincorporated areas as its territory.
Commercial plan review and Kentucky Building Code enforcement both run through that office, so a reroof moves faster when the drawings are complete on the first submittal.
These findings go into photos and notes during the inspection, because each one changes what the permit drawings show.
Cores on older Benton buildings sometimes show a second roof laid over the first. The model code behind the Kentucky Building Code limits recovering over two existing layers, so those roofs come off to the deck before new insulation and membrane go down.
Usually Means: Plan a full tear-off and confirm it with the county office.
Moisture readings mark soaked polyiso, which comes out and gets replaced before any recover.
New or relocated HVAC units add curb openings that the roof drawings have to show.
Retrofit framing to put metal panels over a low-slope roof adds load an engineer checks.
Loose caps and cracked joints call for new coping on continuous cleats, drawn as a detail.
Clear drawings and a matching build pay off on the roof, inside the building and in the schedule.
The deck, insulation, cover board and membrane go down in the order shown on the submittal, so the inspector sees the same assembly on the roof.
Coping caps, edge metal and counterflashing are worked out on paper first, which avoids improvised fixes at the parapet mid-job.
Knowing where curbs and drains change before tear-off lets your staff plan unit shutdowns and protect stock below those roof areas.
Removing every wet board found in the cores keeps trapped water from rusting a steel deck under the new roof.
A complete first submittal to the county office cuts the back-and-forth that pushes a roof start date into colder, wetter weather.
A written assembly from deck to membrane lets you compare tear-off and recover prices for the roof on the same terms.
These are the systems most Benton reroofs end up with, each drawn in full for the county.
Old layers come off to the deck, new polyiso and cover board go down, and TPO roofing or EPDM roofing is installed over them with fresh flashing at every curb.
When cores prove the existing insulation is dry and only one roof is in place, a fastened cover board and new membrane go over it with raised edges.
Light-gauge framing builds new slope above a ponding flat roof so commercial metal roofing can shed water off the eaves.
Call us and tell us where the water is coming in. A temporary repair can hold while the permit for the full reroof is prepared.
This is how a Benton reroof moves from the first core cut through county review to the finished roof.
We cut cores to count layers and check for wet insulation, measure edges and curbs, and photograph the parapet details the drawings will need.
Deck, vapor retarder, insulation thickness, cover board, membrane and edge metal are drawn in section, along with any retrofit framing or new curbs.
The roof package goes to the Marshall County Building Office for commercial plan review, and questions from that office are answered before work starts.
Tear-off, insulation and membrane go down one section at a time, matching the approved assembly, and each section is sealed watertight by evening.
Seams are probed, flashing and coping checked, and the roof is ready for any county inspection before we walk it with you.
Is your property somewhere besides Benton? We take commercial roofing jobs in each town listed here as well. For a town not shown, call us or send us a message.
Where riverfront industrial roofs and retail centers file permits with the city or McCracken County.
Plant and warehouse roofs along the Tennessee River.
Lyon County seat with lake wind at the eaves.
The questions Benton owners raise before a reroof, with a short answer showing on every row.
Yes. The Marshall County Building Office requires permits for construction projects across the county, including Benton, Calvert City, Hardin and the unincorporated areas. It also handles commercial plan review and Kentucky Building Code enforcement. Bring the roof assembly from deck to membrane, the insulation thickness, the edge and coping detail, and any retrofit framing or new curbs.
Only when the old insulation is dry and firm and the roof has a single existing layer. The model code behind the Kentucky Building Code limits recovering over a water-soaked roof or over two layers, and the county office confirms how that applies to your building. Cores and moisture readings settle it.
Show each layer in order: deck, vapor retarder, insulation with its thickness, cover board and membrane or panels. Add the edge metal and coping detail at the parapet, drain changes, and the size and location of any new rooftop unit curbs. Retrofit framing for metal over a flat roof needs its own detail.
It changes what the drawings show. A tear-off exposes the deck for repair and resets edge and curb heights, while a recover adds a layer and raises them. Either way, the county office reviews the assembly that will actually be built, so the choice gets made after cores and before the submittal.
The same Marshall County Building Office that covers Benton. Hardin and Calvert City sit inside its listed territory, so a roof job in either town goes through the same permit and plan review steps. One set of roof drawing standards works for buildings across all three towns.
Tell us about the building and what the roof needs. We will walk it, prepare the details for county review and give you a free estimate.
Want A Call About Your Roof?
Leave your name and number and we will call you back about the roof.
Or call now: (618) 386-4443